When your exterior starts failing, the clock is already ticking. Forge Siding provides full Siding in Nunn, CO — from initial assessment to final cleanup — so your home is protected and your curb appeal restored.
We didn't start Forge Siding to push volume — we built it because homeowners in Nunn kept getting burned by crews who cut corners on material selection, skipped moisture barriers, and left job sites messy. That's not how we work. Every Siding project starts with an honest assessment: we look at your substrate condition, check for existing rot or moisture intrusion, and talk through your options before a single nail goes in.
Every estimate is itemized and written down before we ever ask for a signature. You'll see material costs, labor, disposal, and any underlying repair work broken out separately — so you know exactly what you're paying for and why. We've completed thousands of Siding projects across Nunn, CO and our callback rate is under two percent. That number matters to us.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Compromised siding reduces your wall assembly's thermal performance. If you've noticed climbing heating or cooling costs without an obvious cause, degraded siding — especially if it's letting air infiltrate — is worth investigating.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Vinyl offers the widest color and profile selection of any cladding material, and with the right thickness and a quality insulated backer option, it performs well across most of Nunn, CO. We carry Dutch lap, beaded, board-and-batten, and shake profiles and can match existing siding profiles on partial replacements when the rest of the home is in good condition.
LP SmartSide and similar engineered wood products split the difference between the look of real wood and the dimensional stability of manufactured products. They're primed at the factory, accept field-applied paint well, and hold up to impact and moisture better than OSB or solid wood. We use LP SmartSide Trim & Fascia alongside the panel and lap systems so the trim package matches — no mixing incompatible products that age differently.
Our repair crews use the same material standards as our full-installation teams — no caulking over gaps as a permanent fix, no missing sealant at transitions, no shortcuts on housewrap at the repair perimeter. If there's rot in the sheathing behind the damaged panel, we address it during the repair rather than covering it up.
We work with metal panel systems, large-format fiber cement, and commercial-grade vinyl for multi-family and light commercial applications. EIFS compatibility work, expansion joint detailing, and coordination with waterproofing and window subcontractors are all in scope. We carry the insurance requirements for commercial GC work and can provide certified payroll documentation for public projects.
Soffit ventilation is often compromised during re-siding work when installers don't maintain existing vent openings or fail to add ventilation where it was previously missing. We verify soffit net-free vent area against attic square footage before closing up the overhang — because your roofing contractor will find the problem later if we don't.
Four steps. Each one documented. No surprises at the invoice.
We come out, examine your existing cladding, probe for soft substrate, check flashing and housewrap condition at visible penetrations, and give you an honest assessment of what we're working with. No high-pressure sales — just a clear picture of the project scope before we talk numbers.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
You see the number before you sign — and the invoice matches the estimate. If scope changes come up during demo, we stop work, show you what we found, and get written approval before proceeding. No invoice surprises.
We run our calendar tightly so the start date we give you is the date we're there. If a legitimate delay comes up — major weather, material shortage — we call you the day before and reschedule immediately, not a week later.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Get the Details on Our Warranty — +1-844-782-0929We don't cherry-pick — these are verbatim accounts from homeowners who hired us for Siding work across Nunn, CO.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
A storm took out a whole section of vinyl on the east side of our house. I called four contractors — three of them said they'd have to replace the entire elevation because they couldn't match the profile. Forge Siding's estimator sourced a matching panel through their supplier network and did a clean repair. You can't tell where the new material starts. Saved us probably $4,000 compared to a full-side re-do.
The fascia and soffit on our older home were rotting away and we assumed it would be a nightmare project. Forge Siding quoted it alongside the siding replacement so everything was done in one mobilization. The crew found two spots where the rafter tails had started to soften — they showed me photos before touching anything and walked me through the repair options. The whole exterior looks like a different house now.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Nunn, CO don't do it this way.
We had three bids and Forge Siding was the only contractor who physically checked the housewrap condition before quoting. Everyone else just looked at the surface. They found a section of torn WRB behind the garage bay that needed patching and included it in the estimate. When you're spending this much on an exterior, you want a company that checks the whole wall system, not just what they can see from the ground.
Real questions, real answers — no filler.
Forge Siding sends crews to Nunn and every community within our regional service area. We keep local dispatch units strategically based so travel time doesn't eat into your project day — and so we can respond quickly when there's an emergency siding situation that can't wait.
Our primary service area covers Nunn and surrounding communities within our regional radius. Call +1-844-782-0929 to confirm service availability at your address — we'll tell you same-day.
Free written estimate. Licensed crew. Scheduled start date. Call Forge Siding now and get a real assessment — not a ballpark number over the phone.
Schedule My Assessment — +1-844-782-0929